More than sensors+automation
Search

JUMO Wtrans Receiver - Universal Receiver for JUMO Wireless Measuring Probes (902931)

Features

  • Universal receiver for JUMO wireless measuring probe
  • In combination with corresponding transmitter for RTD temperature probes, thermocouples, resistance/potentiometer, voltage input, or pressure measurement
  • Wiring expenses are eliminated with modern wireless technology
  • For up to 16 transmitters per receiver (can be freely combined)
  • RS485 interface with Modbus protocol
  • Up to four analog outputs/up to two switching outputs (relay)
  • Operation directly on device or by using setup program on PC
  • Customer-specific linearization (40 value pairs or 4th order polynomial)
  • OnlineChart function for recording of measured values directly on the PC

Description

The Wtrans receiver T01 in combination with suitable Wtrans transmitters is used for mobile or stationary measurements of physical measurands. A significant reduction of the installation work is achieved due to the use of trendsetting wireless technology found in the industrial radio frequency 868.4 MHz or 915 MHz. Cable connections are not required. The radio-based sensor technology also functions in a rough industrial environment. The supplied Lambda/four-antenna with an impedance of 50 ohm can be directly screwed on or mounted externally. If the antenna wall holder with a 3 m antenna cable is used then the open air range is 300 m. In the receiver the received measured values are converted, displayed, and are available as linear current or voltage signals (0(4) to 20 mA, 0 to 10 V) and via the digital interface RS485. All receiver outputs are galvanically isolated. A connection to higher-ranking systems (e.g. the system visualization software JUMO SVS3000 or the Modbus master-compatible JUMO LOGOSCREEN nt paperless recorder) is possible via the digital interface with Modbus protocol.
Operation and configuration can be performed via the keypad in conjunction with a two-line LCD display or with a setup program for even greater convenience. This way, parameters such as filter constants, offset, alarms, and drag indicators (minimum and maximum value memory) can be set separately for each channel. For this purpose, a connector is provided on the front for a PC interface with TTL/RS232 or USB/TTL converter for connecting the receiver and the PC. The receiver in the mounting rail case is intended for installation on a DIN rail 35 mm × 7.5 mm according to DIN EN 60715. The screw terminals for the electrical connection are located at different levels. The conductor cross section may not exceed 2.5 mm2.

Take a look how easily the JUMO Wtrans system can be configured (German only).

Documentation
Brochure
Declaration of Conformity / White Paper
Certificate of non-objection
eLearning Course (explanation video about the product)
Software

Please take note of our General Terms and Conditions and Clauses for Paragraph 1.4 General Terms and Conditions.

Article number Product description Price of the full version
00488887

Setup-Program Wtrans

Download  216.exe (30 days Test Version)  (78.0 MB)

additional information
price on request
00549067

Setup program Wtrans inkl OnlineChart

Download  216.exe (30 days Test Version)  (78.0 MB)

additional information
price on request
Accessories

Accessory articles

Article number Product description Price / piece
wall power supply 600mA 3-12V price on request
PC interface with converter USB/TTL price on request
Antenna cable 3m, impedance 50ohms price on request

(in stock)

Wall holder with counterweight for lambda antenna price on request

(in stock)

KCND cable SMA-connector 5m price on request

(in stock)

KCND cable Antenna cable, 10m long, impedance 50 ohm with threaded connector price on request

(in stock)

Antenna cable 10m, impedance 50ohms 125°C price on request

(in stock)

Add.lambda/4 antenna 868MHz 120°C price on request

(in stock)

Add.lambda/4 antenna 915MHz 120°C price on request

(in stock)

Lambda/4 antenna +125°C 10m cable price on request

(in stock)

Lambda/4 antenna +125°C 20m cable price on request

(in stock)

Interface converter - RS232 to RS422/485 price on request
Plug-in card interface - 2xRS422/485 price on request
Activation for OnlineChart price on request
Articles in stock (for more articles see data sheet)
Filter für Verkaufsartikel-Tabelle

Reduce the table of articles by filtering the features

Article number Product description Price / piece

Basic type: Wtrans receiver T01.EC1 with wireless transmission of the measured values, 4 analog outputs

Version: Standard with default settings

transmitter frequency: SRD band 868,4 MHz (Europe)

Voltage supply: AC 110..240V +10/-15%,48..63Hz

price on request

Basic type: Wtrans receiver T01.EC1 with wireless transmission of the measured values, 4 analog outputs

Version: Standard with default settings

transmitter frequency: 915 MHz (America, Australia, Canada and New Zealand) (not in connection with AC/DC 20...30 V)

Voltage supply: AC 110..240V +10/-15%,48..63Hz

price on request

Basic type: Wtrans receiver T01.EC1 with wireless transmission of the measured values, 4 analog outputs

Version: Standard with default settings

transmitter frequency: SRD band 868,4 MHz (Europe)

Voltage supply: AC/DC 20..30V,48..63Hz

price on request

Basic type: Wtrans receiver T01.EC3 with wireless transmission of measured values, 2 analog + 2 relay outputs

Version: Standard with default settings

transmitter frequency: SRD band 868,4 MHz (Europe)

Voltage supply: AC 110..240V +10/-15%,48..63Hz

price on request

Basic type: Wtrans receiver T01.EC3 with wireless transmission of measured values, 2 analog + 2 relay outputs

Version: Standard with default settings

transmitter frequency: SRD band 868,4 MHz (Europe)

Voltage supply: AC/DC 20..30V,48..63Hz

price on request

Other interesting products